NEW BELLS FOR 96

Discussion in 'Fettling Forum' started by CRAZY CRAB, Aug 5, 2020.

  1. CRAZY CRAB

    CRAZY CRAB United Kingdom Subscriber

    Offline
    Joined:
    Jan 5, 2020
    Messages:
    188
    Location:
    addlestone
    GOT 6 bells made, as they are the hardest things to get hold off, plus tryed them, but the holes need to be made bigger, see vid, will get there in the end, these are the Mk1s, so going to have to get a round file out and get filling :) vid -----

    BELLS FOR 96.jpg
     
  2. Ian

    Ian Subscriber

    Offline
    Joined:
    Jul 26, 2004
    Messages:
    6,758
    Location:
    West Yorkshire
    Good stuff! :thumbup:
     
  3. CRAZY CRAB

    CRAZY CRAB United Kingdom Subscriber

    Offline
    Joined:
    Jan 5, 2020
    Messages:
    188
    Location:
    addlestone
    you wait untill you see the vid, :) Ian, posting it later
     
  4. Ian

    Ian Subscriber

    Offline
    Joined:
    Jul 26, 2004
    Messages:
    6,758
    Location:
    West Yorkshire
    Ooh! Looking fwd to it ... :)
     
  5. Twoberth

    Twoberth United Kingdom Subscriber

    Offline
    Joined:
    Feb 21, 2017
    Messages:
    980
    Location:
    England
  6. CRAZY CRAB

    CRAZY CRAB United Kingdom Subscriber

    Offline
    Joined:
    Jan 5, 2020
    Messages:
    188
    Location:
    addlestone
    like it
     
  7. CRAZY CRAB

    CRAZY CRAB United Kingdom Subscriber

    Offline
    Joined:
    Jan 5, 2020
    Messages:
    188
    Location:
    addlestone
  8. Ian

    Ian Subscriber

    Offline
    Joined:
    Jul 26, 2004
    Messages:
    6,758
    Location:
    West Yorkshire
    Got stuff Mr Crab, but please, please do us all a favour and invest in a tripod.
     
  9. CRAZY CRAB

    CRAZY CRAB United Kingdom Subscriber

    Offline
    Joined:
    Jan 5, 2020
    Messages:
    188
    Location:
    addlestone
    a tripod is on me next to get lish :)
     
  10. CRAZY CRAB

    CRAZY CRAB United Kingdom Subscriber

    Offline
    Joined:
    Jan 5, 2020
    Messages:
    188
    Location:
    addlestone
    made holes bigger, still not working to well

     
  11. Jeopardy

    Jeopardy Subscriber

    Offline
    Joined:
    May 26, 2012
    Messages:
    1,605
    If I remember correctly the spacing between the jet and the bottom of the spreader plate is critical here too.
    Are you absolutely sure that the jet isn’t too big?
    Regards
    John
     
  12. CRAZY CRAB

    CRAZY CRAB United Kingdom Subscriber

    Offline
    Joined:
    Jan 5, 2020
    Messages:
    188
    Location:
    addlestone
    holes even more bigger, still needs a bit of work

     
  13. CRAZY CRAB

    CRAZY CRAB United Kingdom Subscriber

    Offline
    Joined:
    Jan 5, 2020
    Messages:
    188
    Location:
    addlestone
    last go for today, 95% there, the jet is ok, just holes on bell just to small, will check the spacing jet to bottom of spreader plate, it might need rasing up abit, around 3mm using this lip stick

     
  14. CRAZY CRAB

    CRAZY CRAB United Kingdom Subscriber

    Offline
    Joined:
    Jan 5, 2020
    Messages:
    188
    Location:
    addlestone
    got this from charity shop, £3, a bit big, but should work, just have to drill out holes, then make a flame spreader, for a 96

    [​IMG]
     
  15. Twoberth

    Twoberth United Kingdom Subscriber

    Offline
    Joined:
    Feb 21, 2017
    Messages:
    980
    Location:
    England
    @CRAZY CRAB well spotted! it should make a good burner bell.
    This post may help. Please let us see the finished product.
     
  16. G1gop

    G1gop United Kingdom Subscriber

    Offline
    Joined:
    May 9, 2007
    Messages:
    1,492
    Location:
    Cheshire UK
    No pic again.
     
  17. Tantra

    Tantra Subscriber

    Offline
    Joined:
    Mar 4, 2018
    Messages:
    325
    Location:
    China
    Good job
     
  18. CRAZY CRAB

    CRAZY CRAB United Kingdom Subscriber

    Offline
    Joined:
    Jan 5, 2020
    Messages:
    188
    Location:
    addlestone
    got to get a 12mm drill